BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   - Forward suspension bracket
      Electronic control by rigidity of shock-absorbers (EDC)
      Removal and installation of a depreciation rack
      Dismantling of a depreciation rack / shock-absorber. Removal and installation of a screw spring
      Check and utilization of the shock-absorber
      Removal and installation of the bearing of a wheel
      Removal and installation of a beam of a forward suspension bracket
      Removal and installation of the lever of a cross suspension bracket
   + Back suspension bracket
   + Steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of a depreciation rack

 REMOVAL

1. Remove a support of a brake and tie him a wire to a body, address the Section Removal and installation of a brake disk / support of a forward brake.

Do not disconnect a brake hose. Otherwise after assembly it is necessary to remove air from system

2. Take out from the holder the ABS cables and the sensor and wear of brake shoes. Rasstykuyte shtekerny connections in a plug box.

3. Disconnect a bar from the stabilizer, having turned off a nut. Hold the stabilizer from a provorachivaniye a wrench.

4. Remove the hinge of steering draft at a rotary support, address the Section Removal and installation of a cable of the parking brake.

5. Check whether the marking of provision of a depreciation rack put at manufacturer is visible. Otherwise put with paint the strip which is continuation of a gap of the basic bearing.

6. Bring under a depreciation rack from below a garage jack that the rack after its office did not fall.

7. Turn off a nut of fastening of a depreciation rack, take out a bolt.

8. Part vents of a rotary support and record its situation. Auto repair shops for this purpose use the special BMW-31-2-200.ки tool.

9. Uncover a depreciation rack.

10. Rasstykuyte shtekerny connection of electronic control of depreciation if it is available, and uncover a cable.
11. Turn off three nuts of fastening (arrow) of a support of a depreciation rack.

12. Press a rotary support the lever, for example the extender of a face head, down so that to overturn a rack outside from a wheel casing.

For this purpose the assistant is required. You watch to damaging a wheel casing. Cover a wing (2). If necessary remove the lower guard of a motive compartment, address the Section Removal and installation of the lower guard of a motive compartment.

13. Squeeze out the big screw-driver or mount the shock-absorber from a rotary support.

Do not separate a depreciation rack from a rotary support rotary motions. It can lead to emergence radial рисок, leading to damage of a rack.


 INSTALLATION

1. Insert a depreciation rack into a rotary support so that marking coincided with situation a vent on a support.
2. Carefully insert a depreciation rack into a wheel casing and fix by its moment 20 Nanometers at the top support.
3. Join shtekerny connection of electronic control of depreciation if it is available, and close it a cover.
4. Establish a cover on a support of a depreciation rack.
5. Press a rotary support a garage jack up to an emphasis. Pay attention to marking on a rack.
6. Insert tightening a bolt and tighten it the new self-stopped nut the moment of 80 Nanometers.
7. Establish steering draft at a rotary support, address the Section Removal and installation of a cable of the parking brake.
8. Establish wheels directly.
9. Fix a bar of the stabilizer by the new self-stopped nut the moment of 60 Nanometers.
10. Join the shtekerny ABS connection and the sensor of wear of brake shoes. Fix connection in the holder.
11. Establish a brake support, address the Section Removal and installation of a brake disk / support of a forward brake.