BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Diagnostics of malfunctions of onboard electric equipment - the general information
   Safety locks
   Fusible inserts
   Chain breakers (thermal relays)
   Relay
   Check of the relay
   Check of glow lamps
   Check of electric motors
   Check of electric switches
   Check of switches of lamps and electric motors
   Check of sensors
   Check of the electric motor of a screen wiper
   Check of a stoplight
   Check of a heater of back glass
   Removal and installation of the switch
   Removal and installation of the sensor of temperature
   Removal, installation and check of a sound signal
   Initialization of remote control of the uniform lock
   Adjustment of range of light of headlights
   Removal and installation of the electric motor of adjustment of range of light
   Replacement of safety locks
   Arrangement of safety locks
   Lighting devices
   Replacement of glow lamps
   Removal and installation of a headlight
   Adjustment of headlights
   Removal and installation of a back lamp
   Monitors
   Removal and installation of the block of the dashboard
   Replacement of lamps of the block of the dashboard
   Removal and installation of the switch of signals of a turn/screen wiper
   Removal and installation of the radio receiver
   Screen wiper
   Replacement of brushes of a screen wiper
   Removal, installation and adjustment snuffled windscreen washer
   Removal and installation of the drive of a screen wiper/cover
   Removal and installation of the electric motor of a screen wiper
   Check and replacement of the pump of windscreen washer
   Work with electric circuits
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of the drive of a screen wiper / cover

Screen wiper drive

1 — the screen wiper console
2 — the screw
3 — the electric motor
4 — a crank
5 — a bolt
6 — the bearing plug, oval
opening

7 — the bearing plug, round
opening
8 — the bearing plug, round
opening
9 — a damper ring, the top part
10 — a damper ring, the lower part
11 — a spring washer
12 — a nut


 REMOVAL

1. Mark position of levers of a screen wiper on a windshield. For this purpose it is possible to use an adhesive tape.

2. Uncover fastening nuts. For this purpose it is possible to use, for example, the small screw-driver.

3. Turn off nuts.

4. Remove both levers of the drive of a brush from the forward passenger.

Do not deform the lever. It can break! Remove the lever from the bearing a special stripper, for example, of BMW-616000.

5. Uncover the left lever up.
6. Turn off a nut on the bearing of a brush and remove the lever upward.

7. Remove an adjusting washer of the lever from the bearing. The washer sits very strongly. Its removal requires a special stripper, for example BMW-616000, address also an illustration 4.

8. Remove rubber consolidation on a forward partition up.

9. Disconnect collars (2) at air channels (1) at the left and on the right. Turn channels to the center of the car. For this purpose disconnect them from bayonetny clips.

10. Remove an insert of the filter of the soaked-up air (3) at the left and on the right, address the Section Replacement of the Filter of Air of Salon.

11. Take out sideways a bracket (4). Disconnect behind the case of the filter (3) and remove it.

12. Uncover an airsupply. For this purpose open eight clips, having taken out the screw-driver pins.
13. Unscrew screws of fastening and uncover the drive of brushes.

14. Uncover a cable, having turned previously on 90 ° all clips.

15. Rasfiksiruyte also remove multiposition shtekerny connection. For this purpose displace the clamp lever down. Thanks to it the plug is disconnected from contacts.
16. Turn off five bolts of fastening of the drive of a screen wiper and take out it.


 INSTALLATION

1. Insert the drive of a screen wiper and fix bolts by hand. Expose the drive so that it reached the position.

2. Fix the drive (A) by bolts in the sequence from 1 to 5 moment of 10 Nanometers.
3. Join shtekerny connection and record it.
4. Establish a cover of cables and record it four clips.
5. Fix by screws a drive cover.
6. Establish an airsupply cover. Fix it by clips.
7. Install the case of the air filter and fix it in front by a bracket.
8. Install filters of clean air on the right and at the left, address the Section Replacement of the Filter of Air of Salon.
9. Insert the air channel into a bayonetny lock and record it, having turned outside. At the end of turn insert the channel at first down at the filter, then press and fix by a plastic collar. Move the channel in different directions, having checked reliability of its fastening. Install the second channel similarly.
10. Put rubber consolidation on a forward wall.
11. Establish an adjusting washer of the left lever of a cleaner and expose according to earlier put marking. You watch that the angle of installation of a brush to a windshield made about 90 °. If the corner differs from specified displace the lever and an adjusting washer. Fix the lever and an adjusting washer by the moment of 40 Nanometers.
12. Fix a cover of the left lever.
13. Install into place both levers of the drive of the right cleaner.
14. Fix nuts by the moment of 25 Nanometers and 15 min. later once again tighten the moment 25 Nanometers.
15. Put on covers fastening nuts.