BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of a trunk lid

Trunk lid

1 — a trunk lid
2 — consolidation
3 — a loop
4 — the gas-filled shock-absorber
5 — a locking element
6 — the Torx screw with a washer
7 — the lock
8 — the plug
9 — the Torx screw with a washer
10 — a connecting bar
11 — the lock with a key
12 — the lock with a code
13 — a stopper
14 — a lock nut
15 — an emphasis with a pusher

16 — an emphasis
17 — a rubber stopper
18 — a lock washer
19 — a nut
20 — a washer
21 — the self-tapping screw
22 — a cap
23 — the adjusting drive
24 — a connecting element
25 — the Torx screw for plastic
26 — consolidation
27 — an emphasis
28 — an emphasis
29 — the handle press
30 — the Torx screw with a washer
31 — the Torx screw with a washer


 REMOVAL

1. Disconnect facing.
2. Extend a cable plait from a trunk lid. For this purpose to a rasstykuyta shtekerny connection of the lighting lamp of registration plate and uniform lock. Fix a cord on plugs.

Leave a cord in a trunk lid that it was simpler to put into place a plait.

3. Mark with a felt-tip pen the provision of a trunk lid at loops (the shooter on an accompanying illustration).
4. Bring a reliable support under a trunk lid or ask the assistant to take it.
5. Weaken screws (1) at the left and on the right. Turn out screws (2).

6. Remove a trunk lid by means of the assistant.


 INSTALLATION

1. Put a trunk lid into place by means of the assistant. Screw screws (1), without tightening them.
2. Expose a cover according to markings and fix by screws.
3. If the new cover is established, adjust its situation.
4. Involve in a cover a cord with electric wires of the lighting lamp of registration plate and the uniform lock and join shtekerny connection.
5. Establish facing, replace the damaged clips.