BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics


Смотрите http://anytrain.com.ua київ харків поїзд.


Removal, installation and adjustment of door glass

 REMOVAL

1. Remove upward an external level of the window mine. At the same time begin from below.
2. Remove facing of a door.

At the car with a side safety cushion disconnect a weight cable from the rechargeable battery and remove a pillow, address the Section "Removal and Installation of the Lock of a Door". Observe security measures during the work with a safety cushion, address to the Section of the Security measure during the work with a safety cushion.

3. Carefully remove foam facing in a back part of a cut of a door, incline it forward so that the lower adjusting screws were free and record in this situation an adhesive tape.

4. Weaken bolts of fastening of a tightening block (an arrow on an accompanying illustration).

5. Incline glass a little forward and take out back upward.


 INSTALLATION

1. Insert glass into tightening blocks.
2. Attach the window regulator switch. If it is necessary, attach a weight cable to the rechargeable battery.
3. Close glass so that there was a gap of 10 mm.

4. Adjust the provision of glass, having reached the following sizes: And = 5.4 mm; In = 10 mm. Address an accompanying illustration. For this purpose displace glass at open blocks in the longitudinal direction or displace a back block so that glass was parallel to a frame. In this situation tighten screws the moment of 10 Nanometers.

5. Rasstykuyte shtekerny connection of the switch of a window regulator. If it is necessary, disconnect a weight cable from the rechargeable battery.
6. Establish facing of a door. If it is necessary, establish a side safety cushion, address the Section Removal and installation of facing of a door.
7. Establish an external level of the door mine so that it behind was aflush with a door edge.