BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of facing of a door

Here removal of facing of a forward door is described. Process of removal of facing of a back door is approximately similar. Differences are described at the end of the Section.

 REMOVAL

1. Disconnect a weight cable from the rechargeable battery. The battery is in a luggage carrier behind the right side facing.

At a detachment of the battery the memories given in electronic blocks, for example, memories of malfunctions of the engine are erased. Address recommendations of the Section Removal and installation of the rechargeable battery.

2. Isolate a negative pole of the rechargeable battery for an exception of casual electric contacts.

3. Turn out a bolt (1) in the air channel.

4. Take out the screw-driver a plafond of the lower illumination of salon, a rasstykuyta shtekerny connection and remove a lamp.
5. Take out the small screw-driver the switch (2) storing of provision of a seat. Rasstykuyte shtekerny connection also remove the switch.

6. Take out the small screw-driver the console of management (3) window regulators and exterior mirrors.

7. Remove the plug as follows:
   - Plug 1: Wring out sideways the small screw-driver a stopper, without taking out it. The switch is taken out upward by the lever mechanism.
   - Plug 2: Press a lock hook down and incline a lock clip aside. The switch is taken out upward.

8. Remove the console of management.

 

9. Take out a peak (4) from an aperture of the door handle and turn out the bolt which is under it.

10. Disconnect facing of a door sideways and from below. For this purpose delay fingers of edge of facing. The arrangement of clips (arrow) is shown on an illustration.

11. Displace facing upward and release it from the central clip and from the top brackets. The clip is on facing inside around (And).
12. Shift the door drive through an opening in facing.
13. Raise and remove facing under the button of blocking of a door (2).

14. If the central clip (1) remained on a door, remove it, as shown in an accompanying illustration and fix on facing.

15. Disconnect a loudspeaker cable. Unscrew screws of fastening and remove a box of a loudspeaker (1).

Observe security measures during the work with a safety cushion, address to the Section of the Security measure during the work with a safety cushion.

16. Rasstykuyte shtekerny connection (orange color) of a side safety cushion. Unscrew screws of fastening and put a safety cushion with a cover upward, for example in a luggage pocket.

17. Disconnect a cable (1) from the internal handle of a door and remove it.

18. If it is necessary, carefully remove foam facing from an internal part of a door.

That glue consolidation remained on polyfoam, it is recommended to remove it breakthroughs at a low temperature.


 INSTALLATION

1. Carefully paste foam facing to a door.

Avoid facing damages as it can lead to emergence of a draft in salon. Glue weight has to be put on all contour of facing.

2. Connect a cable to the internal handle of a door.
3. Fix a side safety cushion on a door. Join shtekerny connection.
4. Fix a box of a loudspeaker and connect the plug.

5. Check whether there are all clips of internal facing of a door. Replace the damaged clips.

6. Establish facing. Pass the internal handle of a door and electric wires through openings. Lay sound insulation (1) around a cable of a window regulator and paste in a facing opening. You watch that the drive of a door was in a plastic support.

7. Insert facing from above over the fixing button. Put it at height of a level of the mine of a door, delay a little from below and record finger-tips at an angle down to a door in five top brackets.

Additions to removal and installation of facing of a back door

Remove the door handle (address an accompanying illustration)
   a) Remove the screw-driver a peak.
   b) Turn out the screw which is under it.
   c) Remove the handle of raising of glass from an axis and remove glass.