BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of the shelf under a headdress

Here removal of the shelf together with blinds of back glass is described.


 REMOVAL

1. Wring out above both facings of the S-rack and disconnect them from two clips.
2. Rasstykuyte shtekerny connection of internal lighting also put a cover with a lamp aside.
3. Disconnect below a seat belt.
4. Remove a seatback. At a back with the pass device for freight cast away a back forward.

5. From a luggage carrier turn off three nuts of fastening of blinds of back glass. Previously mark the provision of nuts. For this purpose lead round a felt-tip pen a washer.

6. Rasstykuyte shtekerny connection of the drive of blinds on the right in salon.
7. Remove external head restraints. For this purpose extend them completely upward, press slightly forward and back and take out upward.

Second option

 REMOVAL

1. Disconnect a peak of head restraints. For this purpose lift a peak, pull it at an angle back and up and take out forward.
2. To Rasfiksiruyta a head restraint also nominate him up. For this purpose a finger through an opening in a hanger under a headdress press the lever of an unblocking and shift it forward, overcoming force a spring. The lever of blocking is on inside of the external directing core.
3. Disconnect a reception part of an average head restraint.
4. Take out peaks of belts from a hanger for a headdress and disconnect together with belts.
5. Disconnect four clips of fastening of a hanger, having unscrewed the plastic screw with crosswise shliyets.

In the presence of the device for pass of freight it is necessary to disconnect six clips.

6. Pull a hanger a little forward. At the same time ask the assistant to press through openings screws of fastening of blinds of back glass in a luggage carrier. From salon pull blinds for side openings up, having at the same time pulled a cover forward. Thus, fingers of fastening of blinds over the resonator of loudspeakers rise.

Otherwise fingers can be hooked, and the hanger cannot be extended forward.


 INSTALLATION

1. Insert a hanger and shift it back. At the same time four support of a hanger have to enter the directing bodies.
2. Fix the shelf from a luggage carrier by three nuts and washers according to markings (6 Nanometers).
3. Insert four or respectively six clips. Screw plastic screws.
4. Insert into a hanger for a headdress belts with peaks. Fix peaks.
5. Fix a reception part of the central head restraint on a seatback.
6. Establish a peak of head restraints if he acted.
7. Insert external head restraints and record them.
8. Join shtekerny connection of blinds of a back seat or cast away it.

9. Fix belts (4) below by a bolt (1) and a washer (2), tighten the moment 50 Nanometers. Address an accompanying illustration.

At installation the pad (3) has to lie above.

10. Join shtekerny connection of illumination of salon and fix facing of the S-rack.