BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of the door lock

 REMOVAL

1. Close a window of a forward door. Open other windows.
2. Disconnect a weight cable from the rechargeable battery. The battery is in a luggage carrier behind the right side facing.

At a detachment of the battery the memories given in electronic blocks, for example, memories of malfunctions of the engine are erased. Address recommendations of the Section Removal and installation of the rechargeable battery.

3. Isolate a negative pole of the rechargeable battery to exclude casual contact.
4. Remove facing of a door.

Observe security measures concerning a safety cushion, address to the Section of the Security measure during the work with a safety cushion.

5. Rasstykuyte shtekerny connection (orange) side safety cushion. Disconnect a pillow, having unscrewed screws of fastening and put it a cover upward, for example in a luggage carrier.
6. Remove the door handle.

7. Carefully remove plastic facing in a back part of a cut of a door, incline it forward and record in such situation an adhesive tape (1).

8. Disconnect at the door lock the nipple (1) and a cable (2).

9. Rasstykuyte shtekerny connection of the microswitch of the uniform lock also take out it down.


 INSTALLATION

1. Check whether there is a clip pad (for the blade) below in the middle.

2. Insert the lock into a door. At the same time a clip (1) (for the blade) the lock enter up into the blade (2) cylinders of the lock.

3. Join shtekerny connection of the electric motor of the uniform lock and record it.
4. Connect the microswitch plug.
5. Insert the nipple and a cable of the drive into the lock.
6. Insert a handle cable into a door framework.
7. Accurately paste foam facing on a door cut.

Avoid facing damages as it can lead to emergence of a draft in salon. Glue weight has to be put on all contour of facing.

8. Install the external handle of a door.
9. Fix a side safety cushion on a door framework. Join shtekerny connection (orange) of a side safety cushion.
10. Establish internal facing of a door.
11. Attach a weight cable to the rechargeable battery. Establish hours. Program stations of the radio receiver.
12. Check operation of the door lock, drive of the lock and uniform lock.