BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of the external handle of a door

On illustrations removal of the handle at the established facing is shown. Two special BMW tools and some experience are necessary for removal. Otherwise it is recommended to remove facing of a door


 REMOVAL

1. Remove a peak on the end of a door.

The peak consists of two parts. At first remove the screw-driver a middle part, then external.

2. Through an assembly opening enter the BMW-513202 tool and raise a safety bar (1) of a lock plate (2) over a safety pad (3).

3. Enter the BMW-513201 tool into an opening of a lock plate (2) and press it at the raised safety bar (1) forward.

4. Take out the BMW-513202 tool.

 

Removal without special tool

 PERFORMANCE ORDER

1. Remove facing of a door.

 

2. Make independently a hook of a wire of Ø of 2 mm. The end unbend at right angle, x = 5 mm.

3. Insert a hook instead of the tool 513201 through an assembly opening in a door end face into an ear of a lock plate.
4. Displace against the stop forward a lock plate with a hook.
5. Raise a bar (1) of a lock plate (2) the screw-driver under a lock pad. In this situation displace a lock plate with a hook (3) forward so that cuts in a lock plate released the external handle of a door. On an accompanying illustration the provision of a lock plate at the removed external handle is shown. 3 - the hook entered an ear of a lock plate.

6. Take away the handle down and pull at an angle down.


 INSTALLATION

1. Insert the external handle of a door into place and press it.

2. Pull a lock plate (2) the BMW-513202 tool or a hook back so that it was recorded a safety plate.

3. Press the external handle and check its work.
4. Establish into place facing if she acted.
5. Insert into place a peak at a door end face. At the same time at first record an external part, then press average.