BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Removal and installation of a forward wing

Observe security measures when performing body works, see the corresponding subsection.


 REMOVAL

1. Wring out the wide plastic pallet a persistent level on a wing.
2. Remove forward side repeaters of signals of turn, address the Section Replacement of Glow Lamps.
3. Remove a headlight peak. For this purpose disconnect a peak inside, wring out from both holders down and unhook.
4. Remove upward protection of an otbortovka.
5. Mark the provision of a forward wheel in relation to a nave. It will allow to establish the balanced wheel in former situation. Weaken bolts of fastening of a wheel on the car standing on wheels. Lift and install the car on supports.

6. Turn off bolts of fastening and remove sideways a peak of a forward wheel casing (1).

7. Turn off bolts of fastening of an internal wing. Take out clips, previously having beaten out pins a mandrel inside. If pins have a cap, at first take out pins the screw-driver, and then remove a clip. Remove an internal wing.

8. Otboltite a wing from a rack And.

9. Disconnect an internal wing from a car rack.

10. Open a door and through a gap turn off a fastening bolt to a car rack.

11. Turn out the top back bolt (the shooter on an accompanying illustration).

12. Turn out the top bolts of fastening (an arrow on an accompanying illustration) covered.

13. Mark with a felt-tip pen the provision of a loop of a cowl.
14. Record a cowl so that after an otvorachivaniye of bolts of fastening on a wing not to damage adjacent details of a body and a windshield.

15. Weaken a bolt (1), turn out a bolt (2).

You watch to losing a washer under a fastening bolt.

16. The wing strongly sits owing to existence of a protective anticorrosive covering of the bottom of a body. Therefore the hair dryer creating temperature not less than + 400 °C is necessary for its removal.
17. Soften the hair dryer with a flat nozzle the top and lower areas of the bottom of a body. Then remove from below in forward area of a prileganiye of a wing a sheeting. It is especially important to make it in this area, otherwise the wing at removal can be deformed.
18. Remove a wing.


 INSTALLATION

1. Clear the adjacent surfaces of a wing. If necessary align a wing.
2. Impose on adjacent surfaces a usual sealing tape for a wing.
3. If necessary restore a paint and varnish covering.
4. Put a wing, approximately expose it and wrap fastening bolts, without tightening them.
5. Establish a cowl and fix it by bolts, address the Section Removal and installation of a cowl.
6. Expose a wing. You monitor dense landing of consolidation around a headlight. You watch a uniform gap on the relations to a door and a cowl, address the Section Body gaps.
7. Tighten all bolts of fastening of a wing.
8. Apply a sheeting on wing inside.
9. Fix holders of a bumper.
10. Fix internally a wing and a peak of a casing of a forward wheel. Insert clips and enter pins.
11. Fix by bolts a forward wheel. Do not oil bolts or plastic lubricant. Establish a wheel so that the markings put at removal coincided. Lower the car on wheels. Tighten bolts of fastening of wheels cross-wise the moment of 100 Nanometers.
12. Insert the top sealant of a wing.
13. Establish the top protection of edges.
14. Fix from above a headlight peak.
15. Install side repeaters of turns, address the Section Replacement of Glow Lamps.
16. Establish an overlay for a wing.