BMW 5 Series E39

since 1996-2001 release

Repair and operation of the car



BMW E39
+ Introduction
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Body gaps
   Removal and installation of a front bumper
   Removal and installation of shock-absorbers of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of the shock-absorber of a rear bumper
   Removal and installation of a forward wing
   Removal and installation of a cowl
   Adjustment of provision of a cowl
   Removal and installation of a trunk lid
   Adjustment of provision of a trunk lid
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of the luggage carrier/cylinder of the lock
   Removal and installation of a gas-filled emphasis of a cowl/trunk lid
   Replacement of a slip / company inscription
   Removal, installation and adjustment of a door
   Removal and installation of facing of a door
   Removal and installation of the door lock
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation of the power window
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and installation of the electric motor of the movable panel of the hatch of a roof
   Removal and installation of a front seat
   Seat belt tension device
   Security measures at the handling of the belt tension device
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and installation of the shelf under a headdress
   Removal and installation of blinds of back glass
+ Onboard electric equipment
+ Schemes of electric equipment
+ System of onboard diagnostics




Security measures at the handling of the belt tension device

   •  Replacement and check of devices of a tension of a belt of a safety / safety cushion have to be made by specialized workshops. Carrying out any constructive changes with the specified devices is not allowed.

   •  If as a result of failure of the car the device of a tension of a seat belt worked, it needs to be replaced on new (work HUNDRED).

   •  Before performance of any works with the device of a tension of a belt it is necessary to disconnect a weight cable from the rechargeable battery. For an exception of casual contact the tip of a cable needs to be isolated.

   •  If not worked tension device was removed from the car, then it is necessary to store it so that casual access to it was excluded.

   •  The device of a tension and the control unit of it are sensitive to blows. If they were dropped from height more than 50 cm, then it is not necessary to apply them.

   •  By production of welding works the clip of the welding machine has to be attached directly in the place of welding. Just in case the control unit of the device of a tension has to be disconnected.

   •  The control unit of a pillow of the safety/device of a tension is under the central console. For an exception of failures in its work do not place in bliz it any magnets.

   •  It is not necessary to subject the device of a tension and the control unit even to short-term influence of temperatures above +90 °C. The damaged elements are not subject to repair and they cannot be opened. Before their installation check again whether the negative cable of the rechargeable battery is disconnected and whether the plug is isolated.

   •  It is not allowed to remove and utilize the seat belt tension device independently at all. Danger of explosion!

Check of system

 PERFORMANCE ORDER

1. After inclusion of ignition a control lamp the pillow of the safety/device of a tension of a belt has to light up and approximately through 4 pages go out.
2. If the control lamp after inclusion of ignition does not light up, it indicates malfunction in system.
3. If the control lamp does not die away or lights up during the movement, in system of a safety cushion there is a malfunction. It is necessary to consider that the safety cushion and the device of a tension do not function.